علوم و فناوری کامپوزیت

علوم و فناوری کامپوزیت

ارائه مدل انتخاب لایه چسبنده کامپوزیت‌های Glass/ABSچاپ سه‌بعدی‌شده با استفاده از مدل ناحیه چسبنده و الگوریتم ژنتیک در راستای بهینه‌سازی جدایش لایه ها

نوع مقاله : مقاله پژوهشی

نویسندگان
1 دانشجوی کارشناسی ارشد، مهندسی مکانیک،دانشگاه تهران،تهران
2 استادیار گروه مهندسی مکانیک، دانشگاه آزاد اسلامی واحد تهران جنوب، تهران، ایران
10.22068/jstc.2026.2096977.1966
چکیده
ضعف ناحیه اتصال بین‌لایه‌ای در قطعات کامپوزیتی چاپ سه‌بعدی‌شده یکی از عوامل اصلی کاهش ظرفیت باربری و بروز شکست زودهنگام است. نوآوری این پژوهش، ارائه یک تابع هدف برای پیش‌بینی و بهینه‌سازی هم‌زمان پارامترهای رفتار ناحیه چسبنده (CZM) در شکست بین‌لایه‌ای مود I کامپوزیت‌های چاپ سه‌بعدی است. برای این منظور رفتار شکست بین‌لایه‌ای مود I در کامپوزیت Glass/ABS چاپ سه‌بعدی‌شده با استفاده از مدل ناحیه چسبنده در نمونه تیر دو بازوی آزادشونده (DCB) بررسی شد. نمونه عددی شامل دو بازوی کامپوزیتی و یک لایه چسبنده در فصل مشترک بوده و تحلیل آن در نرم‌افزار اباکوس انجام گرفت. پارامترهای اصلی مدل شامل سفتی نرمال فصل مشترک، تنش بحرانی آغاز آسیب و انرژی بحرانی شکست مود I در نظر گرفته شدند. برای تعیین پارامترهای بهینه، تابع هدفی مبتنی بر بار بحرانی آغاز جدایش و پایداری رشد آسیب تعریف شد که خروجی ان شامل سه پارامتر اصلی مدل CZM از جمله سفتی نرمال فصل مشترک Kn، تنش بحرانی شروع آسیب tn0 و انرژی بحرانی شکست مود I یعنی GIC به‌عنوان متغییرهای خروجی پژوهش در نظر گرفته شده است. با الگوریتم ژنتیک در محیط متلب بهینه شدند. همچنین، پاسخ شکست با روابط تحلیلی نرخ آزادشدن انرژی و مدول مؤثر مود I مورد ارزیابی قرار گرفت. نتایج نشان داد که ترکیب تحلیل اجزای محدود، مدل ناحیه چسبنده و بهینه‌سازی ژنتیکی، چارچوبی مؤثر برای پیش‌بینی و تحلیل شکست بین‌لایه‌ای در کامپوزیت‌های چاپ سه‌بعدی‌شده فراهم می‌کند.
کلیدواژه‌ها
موضوعات

عنوان مقاله English

Presenting a model for selecting the adhesive layer of 3D printed Glass/ABS composites using the adhesive zone model and genetic algorithm to optimize layer separation

نویسندگان English

behnam lalehabbasi 1
jalil jamali 2
1 Master's student, Mechanical Engineering, University of Tehran, Tehran
2 Assistant Professor, Department of Mechanical Engineering, Islamic Azad University, South Tehran Branch, Tehran, Iran
چکیده English

Weak interlaminar bonding in 3D-printed composite parts is a primary factor contributing to reduced load-bearing capacity and premature failure. The innovation of this research lies in the formulation of an objective function for the simultaneous prediction and optimization of the "Cohesive Zone Model" (CZM) parameters governing "Mode I" interlaminar fracture in 3D-printed composites. To this end, Mode I interlaminar fracture behavior in 3D-printed Glass/ABS composites was investigated using the cohesive zone model applied to Double Cantilever Beam (DCB) specimens. The numerical model consisted of two composite arms and an interfacial cohesive layer, with analysis performed using Abaqus software. Key model parameters considered included interfacial normal stiffness, critical damage initiation stress, and critical Mode I fracture energy. An objective function based on the critical load for delamination initiation and damage growth stability was defined to determine optimal values; the resulting outputs specifically interfacial normal stiffness (Kn), critical damage initiation stress (tn0), and critical Mode I fracture energy (GIC) were treated as the study's output variables and optimized using a genetic algorithm in the MATLAB environment. Furthermore, the fracture response was evaluated using analytical expressions for energy release rate and effective Mode I modulus. The results demonstrated that the combination of finite element analysis, the cohesive zone model, and genetic optimization provides an effective framework for predicting and analyzing interlaminar fracture in 3D-printed composites.

کلیدواژه‌ها English

Numerical analysis
optimization
interlayer failure
Glass/ABS composite
adhesive zone model