Journal of Science and Technology of Composites

Effect of time on healing behavior of microvascular channels based self-healing E-glass fibers/epoxy composite under flexural and tensile loadings condition

Document Type : Research Paper

Authors

1 Faculty of Materials Science and Engineering, K. N. Toosi University of Technology, Tehran, Iran.

2 School of Mechanical Engineering, Malek Ashtar University of Technology, Tehran, Iran.

10.22068/jstc.2020.31823

Abstract

The occurrence of damage is an unavoidable fact in polymer composites. Damage modes in polymer composites are delamination, surface cracking, polymer cracking, etc. The presence of self-healing could extend the service life time of structure via preventing of damage growth. In this study, a self-healing E-glass fibers/epoxy composite based on micro-vascular channels has been fabricated and focused on the repair of the structure through the delivery of self-healing agents. The specimens were fabricated by hand lay-up route, while the fabrication of microvascular channels was conducted through creating solid preforms and then removing them. Since an important factor for effective healing of this structures after damage creation is high fluidity and suitable miscibility in the damage area, so anhydride resin-hardener system was used because of the higher fluidity in comparison to the amine resin-hardener. The aim of this study is to investigate the role of healing time for achieve of system optimum healing efficiency. To do so, microvascular channels with a constant volume fraction (4%) were incorporated in the composites. The flexural and tensile behavior of the specimens were assessed during the different times (0, 4, 7 and 11 days) from the primary damage creation. After damage creation and break, healing agents present in the microvascular channels flowed in the damage area and over a time span local polymerization and restoring of structure were completed. The results showed that, the highest flexural and tensile strength recovery was obtained 59.07% and 68.05% for the specimen after 7 days from initial damage creation.

Keywords

Main Subjects

References
[1] Wu, D. Y., Meure, S. and Solomon, D., “Self-healing Polymeric Materials: A review of Recent Developments” Progress in Polymer Science, Vol. 33, No. 5, pp. 479–522, 2008.
[2] Kaufmann, M., Zenkert, D., Mattei, C., “Cost Optimization of Composite Aircraft Structures Including Variable Laminate Qualities”, Composite Science and Technology, Vol. 68, pp. 2748-2754, 2008.
[3] Emami, M., Aram, E., Mahdavian, A., “Smart Polymers: Self Healing Polymers”, Scientific Quarterly, Vol. 1, pp. 27-38, 1392. (in Persian)
[4] White, S. R., Blaiszik, B. J., Kramer, S., Olugebefola, S. C., Moore, J. S. and Sottos, N. R., “Self-healing Polymers and Composites”, American Science, Vol. 99, No. 5, pp. 392–399, 2011.
[5] Blaiszik, B., Self-Healing Polymers and Composites, Annual Review of Materials Research, Vol. 40, pp. 179-211, 2010.
[6] Saeed, M. U., Chen, Z. and Li, B., “Manufacturing Strategies For Microvascular Polymeric Composites: A review”, Composite Part A: Applied Science and Manufacturing, Vol. 78, pp. 327–340, 2015.
[7] Dry, C., "Procedures Developed for Self-Repair of Polymer Matrix Composite Materials", Composite Structures, Vol. 35, No. 3, pp. 263-269, 1996.
[8] Dry, C. M., "Self-Repairing Reinforced Matrix Materials”, US Pat. 6,261,360, 2001.
[9] Norris, C. J., White, J. A. P., McCombe, G., Chatterjee, P., Bond, I. P., Trask, R. S., “Autonomous Stimulus Triggered Self-Healing in Smart Structural Composites”, Smart Materials and Structures, Vol. 21, pp. 1-10, 2012.
[10] Bleay, S. M., Loader, C. B., Hawyes, V. J., Humberstone, L., Curtis, P. T., “A Smart Repair System for Polymer Matrix Composites”, Composites Part A, Vol. 32, No. 12, pp. 1767–1776, 2001.
[11] Trask, R. S., Bond, I. P., “Biomimetic Self-Healing of Advanced Composite Structures Using Hollow Glass Fibres”, Smart Materials and Structures, Vol. 15 , pp. 704 –710, 2006.
[12] Trask, R. S., Williams, G. J., Bond, I. P., “Bioinspired Self-Healing of Advanced Composite Structures Using Hollow Glass Fibres”, Journal of Royal Society Interface, Vol. 4, pp. 363–371, 2007.
[13] Williams, G., Trask, R. and Bond, I., "A Self-Healing Carbon Fibre Reinforced Polymer for Aerospace Applications", Composites Part A: Applied Science and Manufacturing, Vol. 38, No. 6, pp. 1525-1532, 2007.
[14] Williams, G. J., Bond, I. P., Trask, R. S., “Compression After Impact Assessment of Self-Healing CFRP”, Composites: Part A, Vol. 40, pp. 1399–1406, 2009.
[15] Hamilton, A. R., Sottos, N. R., White, S. R., “Pressurized Vascular Systems for Self-Healing Materials”, Journal of Royal Society Interface, Vol. 9, pp. 1020 -1028, 2012.
[16] Wu, A. S., Coppola, A. M., Sinnott, M. J., Chou, T.W., Thostenson, E. T., Byun, J. H., “Sensing of Damage and Healing in Three-Dimensional Braided Composites with Vascular Channels Composite Science and Technology, Vol. 72, No. 13, pp. 1618-1626, 2012.
[17] Trask, R. S., Bond, I. P., “Bioinspired Engineering Study of Plantae Vascules for Self-Healing Composite Structures”, Journal of Royal Society Interface, Vol. 7, pp. 921-931, 2010.
[18] Norris, C. J., Meadway, G. J., O’Sullivan, M. J., Bond, I. P., Trask, R. S. “Self-Healing Fibre Reinforced Composites Via a Bioinspired Vasculature”, Advanced Functional Materials, vol. 21, pp. 3624–33, 2011.
[19] Eslami-Farsani, R., Sari, A., Khosravi, H., “Mechanical properties of carbon fibers/epoxy composite containing anhydride self-healing material under transverse loading”, Journal of Science and Technology of Composites, Vol. 3, pp. 285-290, 2017. (in Persian)
[20] Muhammad-Umar, S., Li, B., Chen, Zh., “Mechanical Effects of Microchannels on Fiber-Reinforced Composite Structure”, Composite Structures, Vol. 154, pp. 129-141, 2016.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Journal of Science and Technology of Composites
Volume 6, Issue 4
March 2020
Pages 503-510
Files
Share
How to cite
Statistics